So, one of the first things I had to buy was a gimbal.Use the Smooth-Q2 gimbal stabilizer from Zhiyun-Tech to capture smooth handheld footage with your smartphone, and then store it in your pocket. 4 Document release.After switching from the Panasonic G85 to the Fujifilm X-T30 for video work, I knew that I was going to miss the IBIS (In Body Image Stabilisation). Most advanced and full-featured open-source autopilot software. Attach Wifi dongle if youre using RPi 2.Since The X-T30 and the 15-45mm kit are so light, they are well under that with over 200 grams to spare.First impressions were very good. 5-5.6 OIS PZ – 136gThe maximum payload for the Crane M2 is 720 grams. It’s small, light, has a good battery life, and is one of the cheapest gimbals available with enough grunt to carry the X-T30 and lens.Fujifilm X-T30 – 383g (with battery and SD card)Fujifilm XC 15-45mm F3.If you walk deliberately slower and more carefully, you can get smoother footage. PerformanceWalking normally with the gimbal, the footage is quite smooth although you do get a bit of up down movement, kinda like the head bobbing effect in fps games. When using the 15-45mm lens, it needs to be balanced with the camera turned on, since if you balance the camera with it switched off, it would be front-heavy when the camera turns on and the lens extends outwards. It took about 10 minutes following the tutorial on Zhiyun’s YouTube channel and it’s something you only need to do once unless you’re using the gimbal with multiple different devices. Zhiyun Crane M2 in caseBalancing the X-T30 was pretty simple. You can also charge it using any USB power bank while out in the field.IssuesIt’s not possible to balance the Crane M2 with a microphone attached to the camera, not even a small microphone like the Rode Videomicro or the Boya BY-MM1.What Zhiyun recommends is to use the screw mount on the handle to attach a microphone. However, because fuji’s tripod screw hole is’t centred in the middle of the lens as it is with most cameras, the centre of rotation isn’t in the centre of the image as it would be with Sony or Panasonic for example. It’s capable of producing some very smooth pedestal shots (moving upwards vertically from the ground) and some decent approximations of traditional slider shots.Another nice feature is something Zhiyun calls the vortex mode, which spins the camera around its central axis for rotating shots. Some of my favourite shots are achieved with the gimbal attached to a tripod.
It also blocked the pan axis of the gimbal, due to the thumb screw pointing directly down when tightened, hitting against the smallrig arm I was using for the mic.Another issue was the software and support. You can’t use vortex mode any more, for example. This works, but it means you now have a cable going between the handle and the camera , limiting the functionality. Zhiyun Usb Crane 2 Upgrade The FirmwareEventually a new version of the update and calibration tool was released and I was finally able to upgrade the firmware. This begs the question, then, why have it on the website?When I first bought the gimbal, I was never able to get Zhiyun’s software to connect, with or without the USB driver, so I had to keep running the firmware that it shipped with for the first three or four months. However, if you dig a little further into the manual, you’ll find that the USB driver isn’t actually needed, neither for macOS nor for Windows 10. So, the gimbal has to be shipped off to Germany for repair. It still powers on, but the gimbal remains limp, and even updating the firmware has had no effect. Because after leaving the camera charging for about 10 minutes, the gimbal motors stopped working completely. With USB Movie Shooting Auto turned on, When connecting the camera to the USB-C port on the gimbal, nothing happened at all, and when connecting the camera to the Micro USB port here on the tilt axis, I was able to charge the camera using the gimbal, but still had no control.Being able to power the camera from the gimbal is nice, but I’d recommend caution before trying even that. However not other information was provided regarding which gimbals and drones the new features worked with.After installing the new firmware I hound that I now had the new options available on my X-T30 under connection settings. Adobe acrobat crack macThat means there’s really no reason to choose the Crane M2 unless price is your only concern. The Moza Aircross 2 and the DJI Ronin SC are now available for only slightly more money, and give you full control over Fujifilm cameras, as well as having a higher load capacity giving you more flexibility to use some of the bigger, heavier fuji lenses. I was relatively happy with the performance during the 6 months or so that I used it, but the lack of camera control is a real issue, as is the lack of software updates and sketchy support.There are other gimbals much better suited for use with the X-T3 and X-T30. If you’re just looking for a small, cheap gimbal and don’t mind that you’ll have no control over the camera, then perhaps, but it comes with caveats.
0 Comments
Leave a Reply. |
AuthorAmber ArchivesCategories |